Projects/Lidl Balkonkraftwerk Hacking

Project Lidl Balkonkraftwerk Hacking
Naam	Lidl Balkonkraftwerk Hacking
Beschrijving	ESP32 hacking
Website	https://www.lidl.nl/p/tronic-balkon-zonnepanelen-starterset-400-w/p100387536
Start	2025-10-25
Contact	Polyfloyd
Status	Alpha

I bought a solar power set from the Lidl in Germany for just 200 euros. A decent deal for 370 Wp panels, a microinverter and some mounting brackets.

On problem: the microinverter runs Tuya, which is notoriously connected to Chinese clouds. The inverter can be used without setting up network connectivity and the Tuya app, but I would like to have stats from this device in Home Assistant.

So let's hack it!

Teardown

• 
• 
• 
• 
• 

The OEM manufacturer and model is EWAY-VNV6204. Eway makes more power electronics such as car chargers. There are a couple more models in this series such as the EWAY-VNV6208 where the last number corresponds to the wattage.

What is really neat is that the MCU responsible for network connectivity is an ESP32-C3 which I am familiar with. Moreover, it has a 4-pin header right next to it which is most likely UART and a physical push button labeled "BURN" which may very well be a button to put the ESP in flashing mode.

Getting In

Test clamps hooked up

The pad on the UART header farthest from the ESP is connected to a large copper plane. With a continuity test from a multimeter I was able to conclude that this is a ground plane. The two middle pins have thin traces leading to the ESP which means that these are the RX/TX lines. The last pad is probably VCC, I did not measure it.

The board is powered from the DC/solar side. The Lidl Tuya app reports the DC voltage when the sun is hitting the panels, which usually is around 26 volts in slightly overcast weather conditions. The EWAY specs state that the maximum input voltage for this device is 60 volts. Hooking up some probes to the neatly exposed cable connections to a lab power supply with 20V made the board power up.

UART pads marked

Connecting the UART to a USB-dongle gave ASCII output! Hurray! The baudrate is 115200, which is the default for ESP devices.

Holding the BURN button while power cycling triggers the ESP to enter its ROM flashing mode, with which I was able to make a dump of the whole 4M firmware.

Reverse Engineering the ROM

Shoutout to Shiz from Revspace for helping me to get started with Ghidra! o7

I then plowed through the ROM for a few days. I had never done reverse engineering for binaries, so this was a first fun project to discover that. It's quite fun to do. Every function and variable that I identify gives a little dopamine hit. It's a flow-state zen which is similar to programming. I hit a few dead ends in the firmware until I figured out the best way to approach this:

• Find the ESP-IDF functions by searching for their log strings and printfs.
• Find out which of those IDF functions are doing some kind of IO
• Find out what kind of routines are making those function calls

It turned out that really the only kind of IO this device ever does is communicating over its UART1 peripheral (this is distinct from its debugging interface which is UART0).

The peripheral connected to UART1 is wired as GPIO6=TX, GPIO7=RX. It speaks some kind of modbus protocol and answers to address 0xFA. The common 0x2B command for device identification does not seem to produce any meaningful result.

Protocol

Retrieving hardware/software info

>>> FA:01:06:00:F8:FB
                ^^ checksum
       ^^ ^^ cmd
    ^^ addr
<<< FA:01:06:0B:04:00:20:1E:17:DE:FB
                               ^^ checksum
                            ^^ software version
                         ^^ hardware version
                ^^ rated power

Reading sensor values

>>> FA:10:01:00:EE:FB
                ^^ checksum
       ^^ ^^ command
    ^^ addr
<<< FA:10:14:12:09:F4:01:01:0B:52:04:29:01:84:01:D7:00:C2:00:00:00:00:00:F1:FB
                   ^^ ^^ ac frequency * 10
             ^^ ^^ ac voltage * 10

Esphome

I have started building out an Esphome configuration.