Projects/Payphone

Project Payphone
Name	Payphone
Start	2022/02/12
End
Contact	User:Hillebrand
Website
Information	Repair, restore and document a old 1980's payphone to be used to be used as a novelty wall-mounted phone
Status	Alpha

I acquired a old nl:PTT Telecom payphone, type Kimus/Kimas (the name differs, most sources I found called it 'Kimus', but it is stamped as 'Kimas' into the identification plate. I will call it Kimus from now) 2.

It was manufactured somewhere in the mid/late 80's, according to chip dates.

General overview

• Comparable to the German Club Telefon 1. Some parts are interchangable.
• Dialing using both DTMF and pulse dialing, respectively TDK and IDK in Dutch telephony jargon.
• 2 coin inputs on the front, for 0.25 NLG coins ('kwartjes') and 1 NLG coins.
• Amplifier, can be operated using a button on the front
• Separate power supply, 45-60VAC (optional)

Features

Settings

File:Programmeerblokjes Kimus2.jpg

The Kimus2 'programming blocks'.

The Kimus 2 can be set up by a technician using a few plastic 'programming blocks'. Their meaning is noted on a sticker on the inside of the device.

[File:Instelmogelijkheden Kimus2.jpg]

(008 was the former information service)

Translated:

• P1 x 10 = Impulse price (tens of cents)
• P2 x 1 = Impulse price (single cents)
• P3 x 25 = Minimum coin insertion
• P4 x 25 = Internal timekeeping (seconds)
• P5 x 25 = Surcharge per call

P6	Free numbers	Free numbers	008	008	TDK	IDK
	No money	Money	Payment	No payment
0		X	X			X
1		X	X		X
2		X		X		X
3		X		X	X
4	X		X			X
5	X		X		X
6	X			X		X
7	X			X	X

I do not know what 'Internal timekeeping' does. I speculate that 'Free numbers' with/without money means that calling free phone numbers requires money to be inserted. Probably to deter prank calls.

Test features

File:Hoofdprint Kimus2 met testknop gemarkeerd.jpg

The test button, marked in red.

There is a button on the main PCB. Pressing this button will cycle through some test features, described below.

P6	Free numbers	Free numbers	008	008	TDK	IDK
	No money	Money	Payment	No payment
0		X	X			X
1		X	X		X
2		X		X		X
3		X		X	X
4	X		X			X
5	X		X		X
6	X			X		X
7	X			X	X

Wiring

File:Schroefklemmen voor draden Kimus2.jpg

The screw terminals for a external bell, power, and the phone line.

For the bell to operate, the second connector from the top MUST be connected to the connector below (where the jumper is in the photo).

The 48-60VAC is optional. I speculate that it was used for phone booths with a large distance to the exchange, resulting in a low line current, which might cause the electronics to work improperly. My SPA112 ATA seems to supply sufficient current to ring the bell.

The E wire is earth. Needed if you want to simulate cost pulses.

Pictures

blablabla moet dit nog ff invullen obv wiki uploads

Help needed

More info on the technical workings of the Kimus 2 (manuals etc) are very welcome. Romdumps and high quality pictures of the Clubtelefon 1 are also very welcome.

If you are more familiar with reverse-engineering bytecode from ancient MCU's, please get in touch.

I can be contacted at flimpie аｔ bitlair ԁоt nl.

Pictures needed

• Programming plugs on the inside of the door

Useful resources

[1] [2] [3]